Metalwork - Lathe and Mill topics

Saturday, 15 February 2020

Re: TEST was RE: [atlas-craftsman IO] New member, new to me lathe

Robert, though you posted the correct answer, you are graded B- as you didn't attach an explanation of your work. Please show your work in the future. [BIG GRIN]😃

Regards,

Rex

On Sat, Feb 15, 2020 at 6:03 PM mike allen <animal@psln.com> wrote:

loud & clear

animal

On 2/15/2020 2:00 PM, Robert Downs via Groups.Io wrote:

TEST

Robert Downs

_._,_._,_

Groups.io Links:

You receive all messages sent to this group.

_._,_._,_

Re: TEST was RE: [atlas-craftsman IO] New member, new to me lathe

loud & clear

animal

On 2/15/2020 2:00 PM, Robert Downs via Groups.Io wrote:

TEST

Robert Downs

_._,_._,_

Groups.io Links:

You receive all messages sent to this group.

_._,_._,_

TEST was RE: [atlas-craftsman IO] New member, new to me lathe

TEST

Robert Downs

_._,_._,_

Groups.io Links:

You receive all messages sent to this group.

_._,_._,_

Thursday, 21 November 2019

[Amateur-repairs] Test equipment available

HP 3400A RMS voltmeter works well
No power cord very clean has a responds
on all ranges.

Eico 1171 Decade Resistance Box
0 to 999,999 ohms, 1 ohm steps.
Inside looks new, not original knobs.
$50 each plus shipping from 28470 take Paypal,
USPS money order, check, other means of funds transfer ?.
Several VOMs and other equipment available
also a few 100 tubes.
if interested contact Gary W4DCC shalopt at
yahoo dot com. I may make a list.
At 4 score +2 trying to reduce the herd.

_._,_._,_

Groups.io Links:

You receive all messages sent to this group.

_._,_._,_

Saturday, 7 September 2019

Re: [SouthBendLathe] test

Tanks, Jim. Much appreciated!

Stevan S. Yasgur
Suite 550
3300 Edinborough Way
Edina, MN. 55435
(952) 893-9393

steve@yazlaw.com

NOTICE: This E-mail (including attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. §§ 2510-2521, is confidential and may be legally privileged. If you are not the intended recipient, you are hereby notified that any retention, dissemination, distribution, or copying of this communication is strictly prohibited. Please reply to the sender that you have received the message in error, then delete it. This email is not, nor shall it be deemed to be, legal advice or counsel, unless the recipient already has an attorney-client relationship with the firm or me. This email does not create an attorney-client relationship.
Thank you.

On Sep 6, 2019, at 8:14 PM, Jim_B <jim@btdtrf.com> wrote:

Steve;
You are now posting on the Southbendlathe groups.io group.
Ricks posts were on the old yahoo group. Your posts to that group would've bounced.
Allan' posts were from that group also.
I believe I have (finally) turned off posting from that group.
Please pickup your thread from here on this group.

Sent from my MacBook
Jim B.

On Sep 6, 2019, at 9:06 PM, Steve Yasgur <steve@yazlaw.com> wrote:

Jim, here's a test post. I do NOT see any of Rick Kruger's posts/responses from earlier today.

Steve

--
Jim B

Friday, 6 September 2019

Re: [SouthBendLathe] test

I'll repost my last message from yahoo here:

I think the gear is not removable. It should have a smaller OD than
the ID of the bushing, if so, the whole thing comes out the front of
the machine with the bushing. If not, the handle comes off instead,
and the screw comes out the back. There may be a damn-near invisible
pin through the side of the central ball of the handle holding it on.
It is a taper pin, so make sure you are driving the small end, not the
large one. Good luck getting it out.

Also, I'd like to note that the 9 Jr does not have power cross feed,
so you probably have a SCG (standard change gear) lathe, instead of a
Jr.

allan

On Fri, Sep 6, 2019 at 9:14 PM Jim_B <jim@btdtrf.com> wrote:
>
> Steve;
> You are now posting on the Southbendlathe groups.io group.
> Ricks posts were on the old yahoo group. Your posts to that group would've bounced.
> Allan' posts were from that group also.
> I believe I have (finally) turned off posting from that group.
> Please pickup your thread from here on this group.
>
> Sent from my MacBook
> Jim B.
>
>
>
>
> On Sep 6, 2019, at 9:06 PM, Steve Yasgur <steve@yazlaw.com> wrote:
>
> Jim, here's a test post. I do NOT see any of Rick Kruger's posts/responses from earlier today.
>
> Steve
>
>
>
> --
> Jim B
>

--
"well, I stand up next to a mountain- and I chop it down with the edge
of my hand"

-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group.

View/Reply Online (#101789): https://groups.io/g/SouthBendLathe/message/101789
Mute This Topic: https://groups.io/mt/33338087/693790
Group Owner: SouthBendLathe+owner@groups.io
Unsubscribe: https://groups.io/g/SouthBendLathe/leave/2452226/484275076/xyzzy [jhjoshan@gmail.com]
-=-=-=-=-=-=-=-=-=-=-=-

Re: [SouthBendLathe] test

Steve;

You are now posting on the Southbendlathe groups.io group.

Ricks posts were on the old yahoo group. Your posts to that group would've bounced.

Allan' posts were from that group also.

I believe I have (finally) turned off posting from that group.

Please pickup your thread from here on this group.

Sent from my MacBook

Jim B.

On Sep 6, 2019, at 9:06 PM, Steve Yasgur <steve@yazlaw.com> wrote:

Jim, here's a test post. I do NOT see any of Rick Kruger's posts/responses from earlier today.

Steve